Concrete crack repair method

Concrete Crack Repair | 5 Concrete Repair Methods | Crack Repair Techniques | Wall Crack Repair Methods9 min read

Concrete Crack Repair

It is commonly observed that concrete structures face cracking problems during their life period. This crack must be given serious and careful attention and repair at the right time. Concrete Crack Repair involves a lot of time and cost constraints. There are several methods of concrete crack repair methods and techniques.

Choosing the appropriate crack repair method can help you save a lot of time, money, and energy and can give long-lasting results. 

It is essential to know the type and nature of cracks that have appeared in the building to be able to select the most suitable and cost-effective method of repair. It is also important to know the cause of cracks so that they can be corrected to keep the cracks from recurring.


Concrete Crack Repair Methods

The following are the best methods for repairing cracks in concrete

1. Concrete Crack Repair by Epoxy Injections

The Epoxy Injection may be used to bond the cracks having greater than or equal to 0.05 mm opening. 

This method is not suitable for crack is active and if the cracks are large in number, or when the water leakage cannot be controlled.

concrete crack repair
Epoxy Injection

In this method of concrete crack repair, the cracks on exposed concrete surfaces are sealed by injecting epoxy under the concrete crack.

But, it is essential to find and fix the major cause of cracks before injecting the epoxy into the cracks otherwise the cracks will keep on emerging again and again.

Problems such as leakages and silt contamination damage the efficiency of epoxy, therefore it is recommended to fix these issues before injecting the epoxy to make it last longer.

The epoxy injection method of crack repairing requires a lot of discipline and skillful execution so you need to be sure that the person executing the repairs knows his work.

Epoxy resin loses strength when exposed to fire or sustained elevated temperatures and fireproofing protection is required for such structural repairs. MOre

Read More: Which Cement Is Best For House Construction


2. Routing and Sealing

Routing and sealing the cracks is a much more common and much simpler method to repair cracks.

That said, it can be only used in cases where only remedial crack repairing is required and structural repairs are not needed.

Routing and sealing of cracks in concrete can be used for inactive cracks not involving the restoration of tensile strength.

Under this method, the crack is enlarged along its exposed face and the V-shaped groove is formed up to a minimum width of 6 mm and a depth of 6 to 25 mm.

This V-shaped groove is filled and sealed with suitable material. This is a Popular concrete crack repair.

Methods of Repairing Cracks in Concrete

It should be taken care of the width to depth aspect ratio when sealing the joint so that there is enough room left for the movement.

While repairing roadway pavements, pouring hot tar within the cracks is a simple and inexpensive method.

Be careful when using hot joint sealants and make sure that they bond with the concrete and do not melt and flow under operating conditions.

Routing and Sealing Method of Concrete Crack Repair

The material used as the sealant can be of any material that can balance cyclic expansion and contraction and which does not become brittle with time, including epoxies, urethanes, silicones, polysulfides, asphaltic materials, or polymer mortars.

Cement grouts are not to be used due to the chances of future cracking.


3) Stitching the Cracks

Stitching the Cracks - concrete crack repair

Stitching the Cracks is the easiest and long-lasting method of repairing concrete cracks. In this method, a number of the hole drilled along the crack surface and stitched with metallic wire.

This metallic U-shaped wire is then passed through holes and anchored strongly in the holes with grout or an epoxy-based system.

Stitching the Cracks - Concrete Crack Repair
Stitching Cracks

4) Drilling and Plugging

Drilling and Plugging Method of Concrete Crack Repair
Drilling and Plugging

When it is required to repair a vertical crack in the concrete that runs in straight lines, this is a good method for its cost-effectiveness and less time-consuming. 

In this method, holes are drilled vertically in the cracks and a key is formed by passing down a grout. The grout key drilled in concrete helps in preventing leakages.

A Concrete crack can be repaired by Gravity Filling, dry packing, overlay and surface treatments, etc. selection of the method of repair depends on the nature of cracks and whether a crack requires remedial or structural repair.

This is method also known as Wall Crack Repair Methods.


5. Grouting Method of Crack Repair

i) Portland Cements Grouting

In the case of gravity dam and concrete wall large-sized cracks formed. They can be repaired by filling with Portland cement grout.

This grouting method is effective in stopping water leaks, but it will not structurally bond cracked sections.

concrete crack repair
Cement Grout Repair

The procedure consists of,

  1. Cleaning the concrete along the crack.
  2.  Installing built-up seats (grout mesh) at suitable intervals (to provide a pressure-tight connection with the injection apparatus).
  3. Sealing the crack between the seats with cement paint, sealant, or grout; 
  4. Flushing the crack to clean it and test the seal; and then grouting the whole area.

In this method, mixtures of grout may contain cement and water or cement plus sand and water, depending on the width of the crack.

However, the water to cement ratio should be kept as low as practical to minimize shrinkage and to maximize strength. Other admixtures or water reducers may be used to improve the properties of the grout.

For this treatment a manual injection gun may be used in case of small volume crack filling and for larger volumes, a pump should be used.

The good pressure should be maintained for several minutes after the group is filled over a surface to ensure good penetration.


ii) Dry Packing

In Dry packing method, the hand placement of a low water content mortar is done by tamping or ramming the mortar into place to make intimate contact between the mortar and the existing concrete.

concrete crack repair
Concrete Dry Packing Method

As we use the low water-cement ratio for grout mix, there are chances of little shrinkage, and the patch remains tight and can have good quality concerning durability, strength, and water tightness.

The dry pack method can use for the small-sized crack of inactive nature. The dry pack method is not suitable for filling or repairing active cracks.

Before applying grout by dry pack method the slot of 25mm x 25mm must open to a concrete surface. The slot opening should be such that so that the base width is slightly greater than the surface width.

The mortar should prepare 30 min after mixing water to minimize chances of shrinkage and then should be remixed before use. This mortar should be placed in layers about 3/8 in. (10 mm) thick.

Each layer should properly be compacted by a blunt stick or hammer, and the old layer should be scratched to facilitate bonding with the next layer.

The repaired surface should be cured by using either water or a curing compound.


Watch Video: How to Repair Concrete Crack


FAQs:

Can Cracked Concrete be repaired?

Concrete cracks can be repaired by various techniques depending on the crack type. Generally, wider cracks are sealed by patching materials whereas thinner cracks are covered by routing or liquid filler.

What are the best techniques for Concrete Crack Repairs?

Concrete crack repair techniques are dependent on the type of crack to be sealed. However, the best techniques for concrete crack repairs are listed below:
Concrete Crack Repair by Epoxy Injections
Routing and Sealing
Stitching the Cracks
Drilling and Plugging
Grouting Method of Crack Repair

Should you fix Hairline Cracks in concrete?

Hairline cracks are not the major trouble to be fixed in concrete. Even though the repair method is quite unworthy to fix hairline cracks. To do so the cracks are required to be wide opened for fixing.

Concrete Repairing Methods

The following are best crack repair techniques for concrete,
Concrete Crack Repair by Epoxy Injections
Routing and Sealing
Stitching the Cracks
Drilling and Plugging
Grouting Method of Crack Repair

Concrete Wall Repair Methods

The Epoxy Injection may be used to repair wall cracks having greater than or equal to 0.05 mm opening. This method is not suitable for crack is active and if the cracks are large in number, or when the water leakage cannot be controlled.

Crack Repair Techniques

The Best Concrete crack repair techniques are as follows,
1. Concrete Crack Repair by Epoxy Injections
2. Routing and Sealing
3. Stitching the Cracks
4. Drilling and Plugging
5. Grouting Method of Crack Repair

Concrete Slab Repair Methods

A crack in a concrete slab is easily repaired by the stitching crack method. n this method, a number of the hole were drilled along the crack surface and stitched with metallic wire. This metallic U-shaped wire is then passed through holes and anchored strongly in the holes with grout or an epoxy-based system.

How to Repair Cracks In Concrete

The best Concrete Crack Repair methods are 1. Epoxy injection 2. Routing & Sealing 3. Stitching crack 4. Drilling and Plugging 6. cement mortar grout 7. Dry packing method.


You May Also Like:

Share This Post

3 thoughts on “Concrete Crack Repair | 5 Concrete Repair Methods | Crack Repair Techniques | Wall Crack Repair Methods”

  1. You did a great job explaining how a vertical crack could be repaired by drilling and plugging concrete. My brother bought an unfinished house, and he wants to repair the foundation because there is a huge crack on the wall. I will pass him the info so he can start looking for a paving contractor in the area.

  2. roundrockconcrete

    thanks for this very informative post. This will help us as an Austin concrete contractors

Leave a Reply


x

Related Posts

Building Materials List | Building Construction Materials List | Construction Materials List | Construction Materials Name List with Pictures
What Is Building Materials? “Building material is the material which is used for the construction purpose.” Each building material posses ...
Setting Time of Cement | Initial and Final Setting Time of Cement Test | Initial Setting Time of Cement | Final Setting Time of Cement
What Is Setting Time of Cement? Initial setting time gives an idea about how fast cement can start losing its plasticity and the final settin...
Foundation Materials List | House Foundation Materials | Materials Used In Foundation Construction
There are different types of Building Foundation Materials used to the foundation of the house. House foundation materials have prime importance...
powered by RelatedPosts
Scroll to Top
DMCA.com Protection Status