25+ Staircase Components and Their Functions

Parts Of Stairs: Different Components

The Staircase is an important element for any building as it establishes the communication between two different levels. There are almost more than 25+ components of the staircase. However, the construction of the staircase is one of the most complex works while constructing a building.

Apart from a few basic parts of a staircase, there are many other components used while dealing with a staircase. Here, you will find basic information on all such components that you need to know if you are planning to monitor the construction of the parts of stairs at your home.

Parts of a Staircase

The different parts of stairs are as follows,

Parts of Staircase
parts of stairs

1. Stairway or Stairwell

A stairway is a total space in which the staircase is constructed.

2. Step

The step is the basic structural and functional unit of a staircase.

(The major function of this staircase component to facilitate movement from one level to another is executed by the step; hence, it is the functional unit.


A set of steps together forms the staircase, without which the staircase cannot be built, hence it is the structural unit.)

One set of tread and riser together is called a step.

It permits ascent or descent from one floor to another.

3. Curtail Step

The starting footstep of the staircase is called the curtail step.

The width of the curtail step is more than that of the other steps in flight if the staircase is open on one side.

The wider step at the base eases the navigation. It also provides a wider base so that newel posts can be firmly fixed to the floor increasing its stability.

4. Flight

In staircase components, the flight is a continuous series of steps without any breaks. Thus, the total stairs from the start to a landing form a single flight.

Normally, a flight comprises 8-10 steps, after which a landing is provided.

Read More: Types of Stairs in Civil Engineering

5. Tread

The horizontal staircase component on which the foot is laid while ascending or descending through the staircase is called tread.

Tread width is the distance from one side of the stair to another. While tread depth is the distance between the outer edge of the step and the next intermediate riser.

The thickness of the tread is kept the same as that of the flooring. Normally, tread width is kept at 270 mm in residential buildings. Public buildings have a greater tread length of about 300 mm to accommodate more public.

Point to be noted: In a flight of stairs, the number of treads is always less by one than the number of risers.

Tip: If the number of treads is multiplied by the depth of the tread, it gives the horizontal distance over which the staircase is located. This is accurate only for the stairs that do not have nosing.

Staircase - Riser, Tread, and Landing
Flight and landing of stairs

6. Riser

The vertical part or member that provides support to the treads is called a riser.

Rise: It is the vertical distance between two consecutive treads.

The rise in residential buildings is kept at 190 cm while in the case of public buildings, it is limited to 150 cm. This reduction ensures that the transition of people is smooth and nobody falls even in a congested situation.

Tip: Riser-less staircase is also gaining popularity in these years which are known as open-tread stairs due to their aesthetic appeal.

7. Nosing

Generally, a tread does not end at the point of its intersection with the below riser. It is extended beyond the riser to a small length as an overhang, which is called nosing.

Thus, nosing is the horizontal protruding edge of tread in a staircase that is extended beyond the face of the riser.

Nosing is generally rounded at the edge. The length of nosing rarely exceeds 1.5”.

Nosing increases the space to place the foot in a staircase for easy negotiation through the staircase. It provides an architectural effect to the staircase.

8. Scotia

Scotia is the additional block of the material provided the underneath nosing for its support.

It even helps in enhancing the elevation of the staircase.

9. Blocking

Blocking is the additional material block provided in the underside of the steps for support to the step.

It is mainly used in the wooden staircase to prolong its durability.

10. Winder


Winder is a type of step that is narrower at one end. It is provided to avoid allotting a landing while changing the direction of the flight.

By employing a series of winders, a spiral staircase is constructed.

Read More: Staircase Reinforcement Calculation

11. Landing

Landing is a horizontal platform provided between two consecutive flights of staircase components. It allows the person to take a rest before advancing onto the next flight.

If the direction of the stair is to be changed or two flights are to be merged into a single one as in the case of a bifurcated staircase, then landing is provided.

12. Going

The horizontal distance between the successive risers measured from the nosing of consecutive treads is called going.

13. Pitch or Slope

The angle made by the line of nosing to the horizontal in a vertical plane is called pitch.

14. Line of Nosing

Staircase Line of Nosing
Line of Nosing

The imaginary line joining the tip of the nosing parallel to the slope of the stairs is called the line of nosing. It is also called a pitch line.

15. Run

The total length of all the flights in a staircase including the landing width in the horizontal plane is called run.

Components of Staircase- Run, Riser, and Tread
Run In Staircase

16. Handrail

An inclined rail mounted on vertical posts at the ends is provided parallel to the slope of the stair to be held by hand for support during ascent and descent. This inclined railing at a convenient height is termed the handrail.

It is provided on either a single side or both sides of the staircase. In the wider staircase, another handrail is also provided in the middle. It supports the user by preventing an accidental fall. Thus, it is an important component of the safety point of view.

The aesthetics of a staircase can also be increased by providing an attractive handrail.

Read More: What is Plot Area, Built Area and Carpet Area

17. Base Rail

If the baluster ends at a distance from the floor, then at the bottom end an inclined rail parallel to the handrail is provided between the vertical posts. It is also known as a shoe rail. The provision of base rail avoids the second baluster problem.

Staircase Components - Baluster, Newel Post and Hand Rail
Base Rail

18. Baluster

The vertical member on which a handrail is supported is called a baluster. Its one end is connected to the top handrail and the other end is either connected to the bottom rail or embedded into the waist slab.

It also serves the safety purpose of preventing accidental falls. Moreover, it can also be used to increase the aesthetic appearance of the staircase.

19. Balustrade

The entire framework of balusters along with the handrail is called a balustrade. it is an important staircase component.

20. Newel Post

In staircase components, the vertical member at the head and foot of a flight of stairs that supports the handrails by anchoring them is called a newel post.

It is a structural member extending up to the floor or subfloor and bolted into the floor joist.

21. Newel Cap

The top of the newel post is often enlarged to create a proper grip. This top is called a newel cap.

Different architectural shapes are available for the newel caps to improve the visual appeal of the staircase.

22. Soffit

It is the underside of the staircase, i.e. the bottom of the stair slab.

It is sometimes embedded into the construction like a store or bath, if they are provided on the underside of the staircase.

Soffit and Waist Slab

23. Waist

The thickness of the RCC slab on which the steps of the staircase are rested is called a waist. The thickness of the waist is perpendicular to the soffit of the staircase.

24. Stringer

Stringer is a structural member parallel to the slope of the staircase in which steps are embedded for support on either side. Sometimes, nothing is provided in the stringers so that the treads and risers can be accommodated properly in it.

In an open type stringer, its end is cut into the shape of the steps so that a visual effect is created. While in closed stringers, a straight inclined stringer parallel to the line of nosing is provided.

25. Headroom

It is the vertical clear distance between the overhead structure of the staircase and the tread closest to it. In most cases, this overhead structure is the ceiling. A minimum headroom of 2 m is to be provided for the staircase.

You May Also Like:

Share This Post

2 thoughts on “Parts Of Stairs: Different Components”

  1. Pingback: Civiconcepts - Make Your House Perfect With us

  2. Pingback: Civiconcepts - Make Your House Perfect With us

Leave a Reply

Download Construction Excel Sheet

Scroll to Top
DMCA.com Protection Status