What Is the Water Content of Soil?
The water content of the soil is defined as the percentage of water present in soil mass by its weight. Water content data is required for the majority of soil parameter calculations.
w = weight of dry soil
Water content is usually expressed in percent.
For better results, the minimum size of most soil specimens should be approximate as given in Table -1. These data constitute ASTM Test Designation D-2216.
Maximum Particle Size in the Soil (mm) | U. S. Sieve No. | Minimum Mass of Soil Sample (g) |
0.425 | 40 | 20 |
2.0 | 10 | 50 |
4.75 | 4 | 100 |
9.5 | 3/8 in. | 500 |
19.0 | 3/4 in. | 2500 |
IS Code For Water Content of Soil: IS 2720-2 (1973)
Equipment For Moisture Content of Soil Test
1. Moisture can(s)
Moisture cans are available in various sizes [for example, 2-in. (50.S mm) diameter and % in. (22.2 mm) high, 3.5-in. (S8.9 mm) diameter, and 2 in. (50.S mm) high).
2. Oven with Temperature Control
For drying of soil, the temperature of the oven is kept between 105°C to 110°C. A higher temperature in the oven should be avoided by the burning of organic matter in the soil.
3. Balance
The weight balance should have an accuracy of 0.01 gm for specimens having a mass of 200 g or less.
Moisture Content Test Procedure
The procedure for the Water Content of the Soil test is given below,
1. Find out the weight empty container (W1) and also record the number.
2. Take a representative sample of soil in the container. Close the container with its cap to avoid loss of moisture.
3. Take the weight of the combined mass (g) of the closed container and moist soil (W2).
4. Remove the cap from the top of the can and place it on the bottom (of the can).
5. Put the container (Step 4) in the oven to dry the soil to a constant weight. In most cases, 24 hours of drying is enough.
6. Determine the combined mass (g) of the dry soil sample plus the can and its cap (W3).
Calculating Water Content
1. Mass or Weight of Moisture = W2 – W3
2. Weight of dry soil = W3 – W1
3. Water Content =
W (%) = (W2 – W3) * 100 ) x W3- W1
Calculate water to an accuracy of 0.1 % as appropriate based on the size of the specimen.
A sample representative calculation is given in table – 2,
Description of Soil=
Sample No=
Location=
Tested by =
Date of Test =
Observation Table
Items | Container | Container | Container |
1 | 2 | 3 | |
Container No: | 42 | 31 | 54 |
Weight of container, W1 | 17.31 | 18.92 | 16.07 |
Weight of container + Wet Soil, W2Â Â (g) | 43.52 | 52.19 | 39.43 |
Weight of Container + Dry Soil, W3Â Â (g) | 39.86 | 47.61 | 36.13 |
Weight of Moisture, W2 – W3 (g) | 3.66 | 4.58 | 3.30 |
Weight of dry Soil, W3 – W1 (g) | 22.55 | 28.69 | 20.06 |
Moisture Content, w (%)= (W2 – W3) * 100 Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â W3 – W1 Â | 16.2 | 16.0 | 16.5 |
Take Average of above three results =(16.2 + 16.0 + 16.5)/3 = 16.23 %
Moisture Content Formula, w (%)= (W2 – W3) * 100 /Â (W3 – W1) Â
The Final Water Content of the Soil is 16.23%
Important Notes
Most natural soils, which have gravel and are sandy in nature, may have water contents up to about 15 to 20%.
In natural silty or clayed soil water content can be found about 50 to 80% can be found. However, in highly organic soil and peat with water contents up to about 500% is not uncommon.
Different organic soil particles get decompose during oven drying at 110°C. An oven heating temperature of 110° may be too high for soils containing gypsum, as this material slowly dehydrates.
As per ASTM, a drying temperature of 60°C is more appropriate for such soils.
It is recommended the Cooling the dry soil after oven drying (Step 5) in a desiccator. It helps to prevent the absorption of moisture from the atmosphere.
Some standard values of the water content of soil for various types of natural soils in a saturated state are shown in Table 2
Soil | Natural Water Content in Saturated State (%) |
Loose uniformly sand | 25-30 |
Dense uniform sand | 12-16 |
Loose angular-grained silty sand | 25 |
Dense angular-grained silty sand | 15 |
Stiff clay, | 20 |
Soft clay | 30-50 |
Soft organic clay | 80-130 |
Glacial till | 12-16 |
FAQ:
What Is the Water Content of Soil?
The water content of the soil is defined as the percentage of water present in soil mass by its weight. Water content data is required for the majority of soil parameter calculations.
You May Also Like:
- Standard Penetration Test (SPT Test) – Procedure, Test Report
- Specific Gravity of Soil Test with Sample Report
- Compaction Factor Test of Concrete, Result & Calculations
- Specific Gravity Test of Cement – Procedure, Result
- SPT Test | Standard Penetration Test | Soil Penetration Test | Standard Penetration Test Procedure | SPT Test Report
- Concrete Core Test | Concrete Core Test Procedure | Concrete Cores | Concrete Core Sample
How To Protect Yourself From The Scorching Summer Sun
Office Equipment List and Their Uses
How to Draw a House Plan Step by Step
Soak Pit: Meaning & Design
Grasscrete: Types and Cost
20 Types of Contractors In Construction